![]() ![]() If you want to connect your fan to the motherboard, you should check for suitable headers. It is possible to connect a 3-pin fan to the system board with either a 4-pin or a 3-pin connector. How To Install Fans On Mobo FAQ Can I Connect A 3-Pin Fan To A 4-Pin Connector? A secure connection should see the header of the motherboard and the end of the fan connector flush. Line up every side, press the connector gently into the header, and check the connection to ensure it is not loose. Using the guide on the header, align the notch on the connector. A guide on where to plug in case fans on the motherboard is provided. This is where many of the computer’s cooling fans are connected to. If you are unsure where to plug in case fans on motherboards, it’s worth knowing that motherboards have fan headers, which are the motherboard terminals. Most feature a magnet or adhesive tape that you can use to connect them to the case. The fan hub female end connects to a motherboard that branches out to multiple male headers to connect fans. It needs a SATA power connector from the power supply and a 3/4-pin connector from the motherboard’s header to the fan hub. How To Connect Case Fan To MOBOĪre you wondering how to install case fans to the motherboard? There are two methods on how to connect case fans to the motherboard, as explained below: Using The Y-Shaped Fan Header SplitterĪnother method to connect case fans to the motherboard without worrying about power draw is the Deepcool PC fan hub. ![]() You can put the RGB fans on the back or front of the case to see the lights. Follow the steps similar to those of 3-pin RGB fans and connect the 4-pin RGB fan to the fan header on the system board. Keep in mind that a 4-pin fan can connect to the 3-pin connector on the system board. These connectors have four square holes in the front and four cables on the back. You can only apply the 4-pin RGB fan connection method when the connector has four cables, and you cannot connect them to a three-wire connector. These fans are better than others because they are quiet and run silently. In most cases, users prefer using 4-pin fans because they are easy to control. These fans have a higher RPM and are much more efficient and faster. Connecting The 4-Pin RGB FanĤ-pin RGB fans are also known as pulse width modulation (PWM) fans. Put the fans in front or behind the case and secure them correctly. Attach it to the motherboard fan headers.Īfter the connections are made, it’s time to put the RGB fan pinout on the case.Now attach the RGB fan connector to two controllers.Manufacturers usually mark the ports/slots, and so try to locate the RGB marks.You should always ensure that you read the instructions included in the package.Then follow the instructions below: Separate Housing Before proceeding, make sure the power switch is turned off. The way it works is similar in both cases. These pins are yellow for speed sensors, red for power, and black for ground. On the front, it has three square holes and three cables on the back. In general, when compared to a 4-pin fan connector, a 3-pin fan connector is smaller. You can only use the 3-pin RGB fan connection method when the connector has three cables. These RGB fan headers on the motherboard are voltage-controlled and are cheaper and easier to connect. Connecting The 3-Pin RGB Fanģ-pin RGB fans are also known as DC fans. There are three kinds of RGB fan connectors that you can connect to your motherboard.Ī 3-pin and 4-pin fan doesn’t require any technicalities to attach them, while motherboards that lack headers may need some skills to ensure that the connections are functional. However, the connection must not be loose after connecting. The connector doesn’t come with a latch to secure the connection, and so you can easily remove the fan connectors of a motherboard by pulling it out. They plug into the end of a PC fan cable by connecting to the end of a four- or three-pin fan on the system board. The fan connectors of a typical motherboard are four- or three-pin connectors. If the fans are many, you can use the Deepcool PC fan hub or the CRJ Molex adapter. This article details installing PC fans, connecting case fans, RGB fans, and three-pin fans to a MOBO.Īre you wondering how you can plug in additional fans to your MOBO? Use the JBtek Y splitter to split the motherboard headers. Many cooling fans connect to a computer using a standard connector, so adding a fan shouldn’t be a problem. Occasionally, the number of fan connectors is much smaller than the number of CPU fans. The fan connectors of a motherboard give the fans the power to run, and, in many cases, users can control the fan speed. ![]()
0 Comments
Leave a Reply. |